Hello Fellow Yuneec Pilot!
Join our free Yuneec community and remove this annoying banner!
Sign up

Recent content by George

  1. George

    led light system

    Looked at the YouTube info, and no source listed. Is there a source link available? RodeoGeorge
  2. George

    LED sequence and colors

    What state?? You do not have your location in your profile! RodeoGeorge
  3. George

    Converting/Playing .AVC ST10 Files

    Thanks. I'll give that a try after flights today. RodeoGeorge
  4. George

    Camera wires broke off circuit board

    Sorry, but not being a GoPro user I've not looked into that. However, I would not think that the gimble connection would be any different for the GoPro, since both gimbles plug into the same place on the craft itself. RodeoGeorge
  5. George

    Converting/Playing .AVC ST10 Files

    I've searched and cannot find a solution. The ST-10+ saves the video files with a .avc extension. I've tried VLC Player, and several others, and cannot open and play the files. What do I need to either view or convert the .avc files? RodeoGeorge
  6. George

    Camera wires broke off circuit board

    Cool. Looking forward to see the final product RodeoGeorge
  7. George

    Camera wires broke off circuit board

    You could install something like this midway in the gimble wiring, that would pull apart when necessary. New KF2510-3P 2.54mm Female Pin Terminals &Header &Housing Connector Kits RodeoGeorge
  8. George

    Q500 4K Smart mode on the controller not working

    I think you have SMART Mode confused with Return To Home (HOME) Mode. In SMART MODE, it will just hover, unless you command it to move. And it moves in relation to your stick inputs regardless of its orientation (where it's pointing). If I can try to summarize: ANGLE Mode: Forward right...
  9. George

    Hitec Charger Question

    CAll Frank at Carolina Dronz. He included the required cables when I purchased my HITEK from him. RodeoGeorge
  10. George

    Camera wires broke off circuit board

    You can make the same connection with a cable (there was one in my accessories box with the 4K), as opposed to the 3 contacts on the Gibmle Shoe. Here is the link for the 4K Cable: YUNEEC Connection Wire Between Q500-4k and Gimbal And here is the link for the Q500 Cable: YUNEEC Connection...
  11. George

    CGO3 camera SD card problems

    As stated above, spraying contact cleaner into the card slot is NOT recommended. There are components/wires/materials inside the camera which could be adversely affected by the spray. I recommend that you take a piece of cardboard the thickness of an SD card, saturate it with denatured alcohol...
  12. George

    Online Yuneec Vendors

    I sent a message to inquire the exact model (W322, W322a, W322b) of the drone. Waiting for an answer. Rodeogeorge
  13. George

    Online Yuneec Vendors

    I bought my 4K at Drones Plus there in Phoenix. Paid a little more, but had the peace of mind of opening and checking everything before returning to Chino Valley. Also showed him how to repair a broken Q500+ gimble (wired pulled out) while I was there. Tried to get them to throw in a Wizard...
  14. George

    Camera wires broke off circuit board

    I was at Drones Plus in Phoenix, and they had a Q500 in for the "ripped out" wires. They didn't know how to fix it. Upon close inspection, I found that the three solder pads on the circuit board were clearly marked "PWM" "GND" and "VCC". Just resolder the wire to the appropriate pads...
  15. George

    6000 mAh battery and prop guards

    This video is worth watching regarding the most popular batteries for the YUNEEC. A comparison by Carolina Dronz. RodeoGeorge