Hello Fellow Yuneec Pilot!
Join our free Yuneec community and remove this annoying banner!
Sign up

Recent content by Joneshd3488

  1. Joneshd3488

    Which software to use for film making?

    I meant to add, I also used Davinci but found Lightworks much easier to learn and use.
  2. Joneshd3488

    Which software to use for film making?

    If you want a simple yet powerful FREE tool for professional level outcome with 4K or 1080p, you should download and spend an hour or two with Lightworks. The free version won't allow exporting to a CD, but I can't imagine the need for that in this day of electronic sharing. I love it!
  3. Joneshd3488

    ST 16 S-2 toggle switch problems

    Just to clarify, I am referring to how to go about removing K1, the Pan Control rotary knob.
  4. Joneshd3488

    ST 16 S-2 toggle switch problems

    Well, crap! The outer tightening ring of my S2 toggle became loose, so I tightened it only to have it break. Now need to replace and not afraid to do this myself but I'm unsure how to remove the pan control knob to remove the switch board. Any pointers? And, if you still have switches to sell, I...
  5. Joneshd3488

    Bind Multiple CGO3+ to ST16?

    No doubt the input I expected, but was hoping for a different outcome. Unbelievable Yuneec can't/won't resolve such a needed and simple update. Thanks much for your feedback!
  6. Joneshd3488

    Bind Multiple CGO3+ to ST16?

    After searching the forum, I'm unable to find any feedback on this topic, so if it has already been covered in another thread, I hope someone can redirect. Otherwise, my problem is this: I now have two CGO3+ cams complete with gimbal...one stock lens, and one with a Peau 8.25 My goal is to...
  7. Joneshd3488

    Yuneec Steady Cam CGO3+ Hack

    Sorry to bother, and I hate to ask further, but after really studying your wiring photo, I can't tell where your connection points are on the gimbal mount plate. I follow you on splicing the red, black, and white from the 4 pin plug, but my H gimbal mount plate has no wiring, just the 5 pin...
  8. Joneshd3488

    Yuneec Steady Cam CGO3+ Hack

    Much appreciated!
  9. Joneshd3488

    Yuneec Steady Cam CGO3+ Hack

    I just purchased the 8AA version Steady Grip, so can you please clarify: 1. I have the H gimbal mount to swap out. 2. What wiring changes must I make for the new mount to work with the CGO3+? Thanks in advance for your response.
  10. Joneshd3488

    How to find Steady-grip for Typhoon H CGO3+ camera?

    So do you mind sharing a link or contact info as to where this place is in Germany?
  11. Joneshd3488

    ???FPVLR or ITELITE DBS???

    I didn't remove any washers on mine. Instead, I slipped an additional short piece of heat shrink tubing over the threads after twisting them to the position I wanted them to always be in. Then, I shrunk the new pieces tight and applied just a tiny drop of instant glue. They haven't twisted in...
  12. Joneshd3488

    ???FPVLR or ITELITE DBS???

    I have FPVLRs a day had no need to remove anything at all. Fit tight... work great.
  13. Joneshd3488

    Batteries, get them while you can.

    Short answer... no zoom
  14. Joneshd3488

    2-24 Firmware V3.03 and ST16 B30 - Post Your Results Here

    Absolutely... I've always installed new firmware updates since last May and have ended never had ANY problems. But, each one must be done exactly right followed by precise recalibration each time. Excellent calibration steps are here on the forum.
  15. Joneshd3488

    GiFi 7000 mAh battery

    Yes... Sorry I misspoke. 14.6, not 4.6... damned spell check!