Recent content by zebulon

I experienced last year with UAVtoolbox 3.2.2 to pre-program an automated flight with my H3. The result was, that when starting the CCC flight, the H3 approached the starting point and then immediately descended to ground. The reason is, that UAVtoolbox and the H3 flightcontroller interpret the...

Sometimes it happens also with my H3 that when I press the red start button the motors won't start and the H3 responds with beeps. One of the reasons can be you are standing too close to the H3. In such cases I switch the flight mode selection switch to position "sport mode", press the red motor...

The gimbal will become very hot when the camera cannot rotate freely in all directions. - Did you dismount the camera transportation lock? - When pressing the reset button the camera must not be fixed in any direction. Best is to direct the camera to its normal position and avoid any force...

After powering on the H3 it is quite normal, that the ST16s displays after a couple of seconds the message "No SSIDs found". In extreme cases it can take several minutes until the camera link is created. When the message "No SSIDs found" appears, you can tap at the end of the line...

Hi, as I remember it was like this 1. the ST16s was switched on and n o connection with the router existed. Please check on WiFi level of the Android system. Start the flight app on the ST16s. 2. the H3 was turned off. Then I pressed the reset button and kept it pressed. I turned on the H3...

Hi ArcticFrost, I'm flying a H3. I had similar problems connecting the Leica LIONL1P camera with the ST16s after I had performed a firmware reset on the ST16s. With a hint from Steve Carr I was able to isolate the problem. Finally I did a reset on the Leica camera and it connected again to the...

This might be the reason for the wrong time stamp. Usually after poweron of the ST16s I only wait till the controller has finished booting and immediately switch on the H3. Obviously it's necessary to give the ST16s enough time for suffienced GPS coverage before powering on the copter. Many...

The wrong date in the EXIF-Parameter is not a problem only typical for the H520e with the Thermocam. My H3 with the Leica cam ION L1 pro archives every once in a while photos with the timestamp December 1, 2013. During several flights within an hour it can happen, that a whole series of pictures...

Here is a photo of the connector of my H3 battery. maybe it can help you.

Hi Steve, according to your hint, I concentrated myself on the WiFi authorization. As "Forget" and entering a new password on the WiFi level of the Android system were of no success, it turned out that the problem must be inside the camera. Even copying a wireless.conf file with the standard...

I exercised also a firmware reset on my ST16S for my H3. The install process as described in the video above ran without problem, including software update. After that I could operate the camera of the H3 (pan & tilt, receive life video from the camera on the screen of the ST16S, taking pictures...

here is the confirmation with H3 of what Trav discovered. The picture CCC-route_with H3 reveals as flight altitude ~360m, this is above sea level or MSL. The picture CCC-route_with UAV Toolbox has altitude values AGL. The H3 interpretes these relative AGL altitudes as absolute MSL altitudes and...

my experience is as follows: after launch of my H3 and selecting the flight route created with UAV Toolbox V3.2.2 the H3 approached to the first waypoint, hovered for about 2 seconds and then descended slowly to the ground. The route consisted of 5 waypoints arranged in a way that the flight...

Yes, I'm familiar with this video. DoomMeister sent me this link a couple of days ago when I asked how to import .plan files into UAV Toolbox. Both tools together are a comfortable means to prepare an automated flight. My intention is to get step by step familiar with the complete process...

has anybody experience in creating a CCC mission with UAV Toolbox 3.2.2 on a ST16S and flying the mission with a Typhoon H3 with the Leica ION L1 camera? The equipment management section of UAV Toolbox offers only 4 drone models for selection: H480, H920+, H520 and H-Plus. H3 is missing. Same is...