Welcome to YuneecPilots.com!

Sign up and join the fastest growing Yuneec drone community.

Recent Activity

Activity stream for all registered members at Yuneec Drone Forum.

  1. 1504 El Paso TX replied to the thread I Need Troubleshooting Help - Motor Failure During Flight.

    Hi, I had similar problem and had to send drone back to manufacture for repair. Now three weeks later I received drone back after repair...

    Feb 25, 2017 at 10:18 PM
  2. RodneyJ replied to the thread Hello from Kansas.

    Will do !!

    Feb 25, 2017 at 10:15 PM
  3. 1504 El Paso TX None »

    Feb 25, 2017 at 10:09 PM
  4. 1504 El Paso TX set their location as El Paso TX.

    Feb 25, 2017 at 10:09 PM
  5. Gogittum replied to the thread GPS Tracker advise.

    You're about to get more so. 2 weeks ago I flew my Q500+ from my semi-rural front yard. After a fairly long flight I was out about...

    Feb 25, 2017 at 9:47 PM
  6. Steve Carr replied to the thread I Need Troubleshooting Help - Motor Failure During Flight.

    You can connect the H to the GUI and it will run a diagnostics test. You can test the motors while it is connected to determine which...

    Feb 25, 2017 at 9:34 PM
  7. ChadCloses liked ThunderChicken's post in the thread FAA Waiver and firmware updates.

    I'm in luck! I never throw anything away like licenses and software keys. I still have the waiver.

    Feb 25, 2017 at 9:21 PM
  8. ChadCloses replied to the thread Wizard Wand.

    I haven't even taken my wand out of the box. Let me know how it goes. Sent from my iPhone using Tapatalk

    Feb 25, 2017 at 9:20 PM
  9. jazzman81 posted a new thread.

    I Need Troubleshooting Help - Motor Failure During Flight

    I was flying my hex, it was in a low hover, about 30 meters up and about 30 meters behind me... there was a light breeze. Out of no...

    Forum: Typhoon H Discussion

    Feb 25, 2017 at 9:20 PM
  10. jcowgar liked Roach's post in the thread NEW Firmware V3.03 and ST16 B30 Available now.

    Good to Go! Thanks, I missed binding the transmitter.

    Feb 25, 2017 at 9:19 PM
  11. Steve Carr liked CraigCam's post in the thread NEW Firmware V3.03 and ST16 B30 Available now.

    Just tried my first flight with new firmware. In my opinion, my right stick is less jerky in turtle mode so it's "smoother". The...

    Feb 25, 2017 at 9:02 PM
  12. Gogittum replied to the thread h after flight path.

    I'm sure this has been asked before, but I'm on this page right now and curious - do you have a version that will work with the ST10+ ??...

    Feb 25, 2017 at 8:59 PM
  13. Rubik replied to the thread NEW Firmware V3.03 and ST16 B30 Available now.

    Hold it! What happened to the CGO3+?

    Feb 25, 2017 at 8:59 PM
  14. Steve Carr replied to the thread Skyview Goggles.

    If they connect with the HDMI cable then you will see the same screen that is displayed on the ST16. However, you would always have to...

    Feb 25, 2017 at 8:58 PM
  15. Roach replied to the thread NEW Firmware V3.03 and ST16 B30 Available now.

    Good to Go! Thanks, I missed binding the transmitter.

    Feb 25, 2017 at 8:56 PM
Loading...