Hello Fellow Yuneec Pilot!
Join our free Yuneec community and remove this annoying banner!
Sign up

Recent content by jimmy1570

  1. J

    H520 Camera problem after update

    hello can any one help.. i have updated the unit, but the camera still flops on boot up.. and wont centralize itself. even after update.. once i hold the camera central on boot up.. after couple minutes it actually center's itself... but when power down, again it wont do its dance and...
  2. J

    H520 Camera problem after update

    hi so did all that, the camera still wont on start up centre or do it start up dance.??? the only this i didnt do was the sensors on the drone . for compass etc. wiill that not allow the camera do take it start position.??? thanks as i manually have to hold camera for couple mins until it locks...
  3. J

    H520 Camera problem after update

    this is 2nd time ive used this drone im normally a dji man.. but ive always luv this drone so i bought one... so im not using anything to retrieve logs... so can i get rid of the message then??
  4. J

    H520 Camera problem after update

    these doc.firmware 1gig??
  5. J

    H520 Camera problem after update

    thanks so the qgc just ignore that message with the px4 ,and will it cotinue to pop up.. thanks and i have tried firmaware yet ill let u no thanks
  6. J

    H520 & E90 updates

    truly appreciate it hope it works thanks
  7. J

    H520 Camera problem after update

    also the controller states Qground control supports px4 pro firmware version 1.4 and above you are using version prior to that which will lead to unpredicteable results, please upgrade your firmware.. but when i go to the controller upgrade theres no upgrade help
  8. J

    H520 Camera problem after update

    Hi can someone help please i bought a h520 and was working good.. for the 2 times i used it.;; Then i was playing and set the new location after i did a update via the controller and it all went thro on 3 items controller /camera/drone. and then i tried calibrating the camera for 1st time...
  9. J

    q500 GPS module pin-out

    ive marked where the missing voltage are
  10. J

    q500 GPS module pin-out

    on the gui all passed finally .. we dont no if the previous owner had issues with the esc... but i can not start the motors tho , the compass shouldnt have anything to do with the motosr to run?? or is it like u said , the main cpu will not initialize properly without the compass, thanks jim
  11. J

    q500 GPS module pin-out

    AWESOME TRULY appreciate it.. ill keep u in touch if i find anything strange with the main pcb on the 1st drone.. with the current sensing cct
  12. J

    q500 GPS module pin-out

    He just bought another on ebay so we can finish 1 out of 2 that he bought.. this other one he bought is flashing Its not connecting, on wifi ..THAT WILL BE OK.. Flashing blue and orange ?? what that normally mean.. also the main led on the main board whats color should that be when powering...
  13. J

    q500 GPS module pin-out

    he had bought it from ebay as selling for parts... so what i just found there is 3 boards the same 1517 and 1 1530 which there should be 2 of each correct??? there is a 1530 on rear left on b motor and there should be the same on rear a motor thats correct isnt it???? the fronts have 1517 pcb
  14. J

    q500 GPS module pin-out

    also with these units is there any easy way to check the esc boards from front to rear.., as someone has played with this unit big time so i want to check all ta
  15. J

    q500 GPS module pin-out

    thank you for promt reply.. yes you got it spot on, and thats what im thinking powerchips.. so the main resistor is a 10k that feeds the powerchip, and also runs to the transistor just under the power chips.. , so basically i jumped the power chip with the 12volt line and all fired up...i...