Recent content by JoeCowboy

Just an update on my testing with the CGO4+ on my Yuneec H920 and ProAction. I tested the SR24 I purchased of of eBay and plugged it into the CGO4+ but it still would not go into bind mode. The SR24 on the CGO4+ would not broadcast it's ID. So I took the top back off of my GB603 gimbal and...

Thank you, I see the Camera WiFi SSID but not the Model SR24 ID for the CGO4 gimbal. Still leads me to believe the SR24 board is not working right. I have another one on it's way should be here in the next couple days. Then I will plug it in and see if it shows up.

Is the orange LED blinking slow or fast? It is a steady blink every second. Fast is bind mode How do you put the SR24 board on the CGO4 into bind mode? The SR24 ID does not show up on my ST24 Bind Model column.

My GB603 has a red LED lit up on it's board when it's turned on. So maybe it's just showing there is power on the main board?

What does the red LED mean across from the MPU6050 port on the main board to the left of the ST24 board in the CGO4?

English Translation: so I have to buy a st 24 for the cgo4? because in mine there isn't one... looking at the photos you sent me there is....Thanks you were helpful I'm waiting anxiously I soldered the ground wire back connecting it to the ground on the power in. I cut the heat shrink off and...

Here is the link to the Post for the CGO4+ pics: https://yuneecpilots.com/threads/a-few-questions-about-the-cgo4.21087/post-254335

Here are the pics inside the CGO4+ that I have. As you can see the ST24 is disconnected and you can see mine has the antennas are poking out from the gimbal housing too. You can also see the light blue wire has been cut on the UART plug and this is the ground wire. As you can see from the...

I attached my Yuneec GB603 gimbal to the Proaction+ and it controlled it so I guess this is all still PWM and switching to reading PWM signal with the ESP32. Anyway here are some pics from inside my GB603 gimbal. I know it's off topic. I will attach more pics from inside my CGO4+ later.

Quick question has anyone ever tried to read the YMAVLINK TX protocols from the Yuneec ProAction+ using a serial connection? I don't have a Yuneec H920+ to try and read them from the drone. I am using the ESP32 and trying to read the TX. Should I hook the CGO4+ gimbal up to the ProAction+ and...

Question on wiring up the attached images. I purchased the CGO3+ gimbal cable to plug into the gimbal connection board. I am going to cut off the 4 pin plug end from the CGO3+ gimbal cable and connect the output of the step down buck power board for 12 volts to the cable then male plug in of...

Started on the Arduino software layout. Getting the WiFi interface setup. Still waiting for the multiplexers to come in. Should have rest of the parts in over the next week! Any feedback would be great!

Found @dylanfm ESP32 Arduino code. Along with @h-elsner help, great stuff: https://yuneecpilots.com/threads/cgo3-serial-link.18528/post-208460

Thank you @Vaklin and @h-elsner for the awesome info and work on coding on your projects. That's why I want to create a "Black Box" for the Yuneec H920 using an Arduino. I purchased EPS32 wifi with one of those small OLED screens just as cheep to buy with screen as not off of eBay. Also...

@h-elsner Looks like you are right about the RX and TX of the CGO4 for Yuneec H920 Plus ports found this info on another thread post: https://yuneecpilots.com/threads/pan-tilt-wont-work-deep-thought-troubleshooting-help.9446/post-105461 Talks about the mTX / PWM and mRX are serial pulses and...