Recent content by matyphoon

Thanks for the proecedure. I tried resetting it, tried, re-uploading latest Camera/Gimbal firmwares but still no success :( I'll give a try to Yuneec Support to know what this beeps sequence mean... Strange since the camera in very good condition (never hit anything on ground or did something...

Light sequence is : white, then blinks between red and green and ends up white until I connect it to CG03 Android App or the ST16. Pan and tilt buttons on the ST16 look OK. I guess there is no link with the drone or the ST16 itself, as I have same beeps (4 long and 3 short, continuously) when I...

Hello, My CG03+ was perfectly working up to today. Nothing special happened but whenever I start it, the CG03+ emits 4 long beeps followed by 3 short beeps continuously. Video works but the gimbal is slightly shaking and I am not able to get it working. I tried it in my ActionCam and get the...

Correct ;) Regarding Typhoon 4K the only command that seem not to work is the gimbal tilt and pan. When I try to pan, the gimbal make noise but stays on same position. Anyway, I'll let you know during my next flight if return home works with this profile.

I checked Hardware Monitor and switch is OK. I did few more tests at home and there is actually a "Select Model" option which looked wrong to me on the ST12 : it was set on H520. For a reason I ignore, Typhoon H is not available from this list, I can choose only among Typhoon 4K, Typhoon Plus...

ST12 is an additional controller I got not from the original pack. No problem with rth and the original ST16.

Unfortunately, this is not possible : when setting "team mode" on the st16, it makes the st12 available for pilot only. Has anyone faced this situation? Flying with not having the return home feature does not make me comfortable! What about loosing the connectivity during flight.... not sure...

Hello, In order to use dual pilote mode, I got an ST-12 along with the original ST-16. Camera is controlled by the ST-16 and drone by the ST-12 controller. Everything works fine except "Return home" button that has no effect when using it. I tried the ST-12 in standalone as well and have the...

OK, found this interesting topic : HOWTO: Update E, F, J, K to Standard (A) firmware, if latest version is already installed (v3.04) @FlushVision, did you try it ?

Thanks a lot for your feedback. I'll pay more attention on my next flights to see if there is a link with the landing gears. But the fact that I faced the same problem with the Actioncam makes me thing there is no link. But as you mentioned, it is clear that once connected the 2nd time, I do not...

The firmware is 3.2.34 (E) so I guess it is EU version? I got it from Amazon France. I haven't noticed any link with the landing gear.

Hello, I face a strange issue both with ST16 and the Actioncam : as soon as the Wifi is available, the ST16 or my Android App connects to it and I have the liveview. However, after 1-2 minutes I always loose the signal, just as if the CG03+ was rebooting. After a second connection, I keep the...

Hi Murray, Thanks for your feedback. I did use the search feature first and had a look at the answers (Search Results | Yuneec Drone Forum). Unfortunately, discussions confirms that it is possible to use the ST12 with the Typhoon H but nothing related to the specific problem I have : my ST12...

Hello, I just got a ST12 controller and plan to use it in Team mode with ST16 on my Typhoon H. However, when going in "Model Select" on the ST12, i only have Typhoon+, Typhoon 4K, Chroma and H920. Do i need to upgrade the ST12 firmware? Where can I find it since nothing is there on Yuneec...

Hello, I just got a Typhoon H equipped with CGO3+ camera. I was about to develop an App to use/control camera gimbal but figured out that the SDK was for H520 :( Is there any chance that the Typhoon H becomes supported by the SDK one day ? Thx