Hello Fellow Yuneec Pilot!
Join our free Yuneec community and remove this annoying banner!
Sign up

Recent content by Varsaggo

  1. V

    Breeze 4K free spare parts

    ahh yes I been there last year ha D to buy another one to get parts to make one working one. I'm always looking for parts for these I'm making a drone out of breeze hardware on a custom race/ freestyle drone Chasis , so always interested in parts if u get rid of it or can't find a way to repair...
  2. V

    Can someone read this flight log and let me know what they see?

    Lol yes I am starting it on the ground and flat surface , just tried to take off with controller and the back power light went teal and it took off and hovered fine but I had no control and the light was teal it luckily just stayed where it was supposed to and after anóther 30 seconds the light...
  3. V

    Can someone read this flight log and let me know what they see?

    Ok so I was not flying the last 2 days due to hurricane so I went to fly today and noticed the drone was just moving backwards all by itself , I figured ok probably controller so I landed and took off in pilot mode and it now was moving backwards twice as fast . So by instinct after letting it...
  4. V

    BREEZE!! GEOFENCE +500M

    I'm using the green apk and as u had said here with the drift, i noticed at least on my one breeze I've tested that if i let go of the forward joystick and I had speed all the way up , so the drone would drift until momentum was lost , that if i watch where the drone is when i let go , no...
  5. V

    Easiest way to install a 11.1v 2200MAH 3S Lipo

    I have done this on two so far the other I actually soldered leads to run out to connect the battery. Being as the stock batteries are known to fail I used one of the cases to make a connector to the bigger 2200mah battery as u can see in the pics below , u can slide in the case first till it...
  6. V

    What capacitor should I use ?

    Yes exactly what it looks like and unfortunately the amount of gap between the board for the lidar and the m7 ESC board is very small. It wouldn't be a problem for the modifications I made for mine since my lidar board now lays free floating with a small amount of rubber and foam attached to the...
  7. V

    What capacitor should I use ?

    Opposite side of the bottom pic u posted , looks like the placement of the lidar board either was originally supposed to go there and be part of that PCB m7 and not a separate board or the placement of that lidar board nixed the capacitor plans ?
  8. V

    What capacitor should I use ?

    Actually looking at the ESC on the breeze at the top of each row of mos fets on the backside of the pcb it looks like they originally thought about putting a cap for each side of the drone. Probably since they aren't really needed for the cost they cut that idea out in the final manufacturing...
  9. V

    What capacitor should I use ?

    Also wanted to point out not voltage surges like u get in AC but say inconsistent voltage when the motors go from hover or decent to full the voltage from the battery can be unable to keep up with the demand that quickly so what u get is a moment where not enough power is being delivered to all...
  10. V

    What capacitor should I use ?

    Yeah I actually found these two wires I had attached to the lidar PCB were running behind the power switch over the second compass/gps chip 😂, I been wondering why I had to recalibrate after every flight , so as u can see in the pic I just rerouted them to this location, Tucked behind the...
  11. V

    What capacitor should I use ?

    It's not bad it's just a freeze in the recording after any kinda major voltage spike, like descending 20feet and letting the throttle go so the craft has to ramp up to catch it's self , I can get it to happen on both Yuneec drones , so after some investigation I found some possible fixes , it's...
  12. V

    What capacitor should I use ?

    Umm like when under full acceleration upwards and then letting the throttle hold in hover quickly causes video to freeze sometimes while recording also causes video breakup , due to the voltage spiking when the draw whent full and then suddenly is released . The the capacitor also helps take...
  13. V

    What capacitor should I use ?

    Lol , good point !! Umm yeah it's for cleaning up the voltage delivered to the ESC and other PCB usually u can do 4 , one on each motor or one at the main terminal connection "The additional drone capacitor functions as an electronic filter. In general, a filter is configured to remove unwanted...
  14. V

    What capacitor should I use ?

    Anyone know what would work best for the ESC ? I know it should be low ESR I believe one of these or maybe all of them might be low ESR but before I go soldering one on , any opinions or thoughts ?
  15. V

    How would one get rid of an Unwanted rotation on the vertical axis??

    Ok well it's been rainy here and havnt been able to fly but finally was able to get it up in the air and it was fine today lol. Now I noticed the day I was having issues the mag Eric field readings around my house were around 175ut compared to the normal 52ut. So wondering if that had something...