Hi again Pilots. Hope you're doing well [emoji6].
I finally had the time to test the h520 and it Seems to fly pretty well. I've used 3 batteries and had no problem flying it, but I think I had over-sized the micro sd card, a sandisk extreme pro 128gb v30, because when I press the photo button it takes ages to have the soft button ready again for another photo and after the third one it just stays thinking. .... I cannot record videos either, It just keep thinking ( actually the firs 2/3 photos are taken).
The card works perfectly in my pc.
Once I got home, making some test on the card I have found out the second problem.... my new e90 was shaking vertically, tiny moves up and down.
I tried to re install the camera, gimbal calibration, but nothing have changed.
Looking at the rc monitor windows I saw that the k2 "sensor" was shaking and unfortunately also the k3 was shaking but I bit less.
K2 and k3 was shaking even with the drone turned off so I thought it was a TX problem instead of a defective e90.
I finally let the TX charge overnight to test it again In the morning because It was at about about 35%when I got home and 15%when I finally went to bed.
The next morning and 100% battery, I test everything again and guess what..... No problemo anymore. [emoji58] Whattt.??
Everything was fine but me.
So I start testing everything again and I have noticed 2 things, the first one was that I could move (using really small force) the k2 for about halfway without actually moving the indicator ( the camera was moving instead) and the second one, that I was testing for a lot of time and the st16s battery was under 35% and here the shaking again.
I have no idea whose fault is that.
I know for sure that k2 is not working well even with 100% battery.
I don't understand why everything start with " low" battery... And why both k2 and k3.
I have update everything so I'm not sure if the problem was there before.
I think I'll have to send at least the TX back to yuneec ... And don't forget about j3 problem .... Fixed with calibration . [emoji22]
I finally had the time to test the h520 and it Seems to fly pretty well. I've used 3 batteries and had no problem flying it, but I think I had over-sized the micro sd card, a sandisk extreme pro 128gb v30, because when I press the photo button it takes ages to have the soft button ready again for another photo and after the third one it just stays thinking. .... I cannot record videos either, It just keep thinking ( actually the firs 2/3 photos are taken).
The card works perfectly in my pc.
Once I got home, making some test on the card I have found out the second problem.... my new e90 was shaking vertically, tiny moves up and down.
I tried to re install the camera, gimbal calibration, but nothing have changed.
Looking at the rc monitor windows I saw that the k2 "sensor" was shaking and unfortunately also the k3 was shaking but I bit less.
K2 and k3 was shaking even with the drone turned off so I thought it was a TX problem instead of a defective e90.
I finally let the TX charge overnight to test it again In the morning because It was at about about 35%when I got home and 15%when I finally went to bed.
The next morning and 100% battery, I test everything again and guess what..... No problemo anymore. [emoji58] Whattt.??
Everything was fine but me.
So I start testing everything again and I have noticed 2 things, the first one was that I could move (using really small force) the k2 for about halfway without actually moving the indicator ( the camera was moving instead) and the second one, that I was testing for a lot of time and the st16s battery was under 35% and here the shaking again.
I have no idea whose fault is that.
I know for sure that k2 is not working well even with 100% battery.
I don't understand why everything start with " low" battery... And why both k2 and k3.
I have update everything so I'm not sure if the problem was there before.
I think I'll have to send at least the TX back to yuneec ... And don't forget about j3 problem .... Fixed with calibration . [emoji22]
Last edited: