Hello Fellow Yuneec Pilot!
Join our free Yuneec community and remove this annoying banner!
Sign up
WTFDproject
Reaction score
3,177

Joined
Last seen

Profile posts Latest activity Postings Media Albums About

  • Hi I live in UK and have been trying to find gui for my chroma blade and can't seem to find it anywhere just want to check drone and raise height restriction to about 100 feet I'm completely new to this so have zero knowledge how the firmware works
    WTFDproject
    WTFDproject
    This link has the Chroma GUI in it. Let me know if it does not help. Please be aware the USB cable must be the "data capable" type. The standard USB charging cables will not work. They look EXACTLY the same, which has caused tons of confusion over the years.
    After doing a system reset on my St10+ Controller, I'm unable to bind my Q500 4K. The drone model isn't displayed for me to select on the Controller. I can put the Q500 4K into bind mode, however it never connects. I also tried to update the firmware using the Q500 Gui and I'm unable to connect. It displays a message that there is no response from the quadrotor....
    Im haveing problems with data pilot and uav toolbox crashing. I have uavtoolbox installed on my ST16 and laptop. I have data pilot on my laptop, and also an android emulator. Data Pilot wont even boot up. UAV toolbox on my ST16 crashes when I try to plan a mission, and the mission block on my laptop wont activate. Am I doing something wrong or what?
    WTFDproject
    WTFDproject
    You mentioned Data Pilot, which I normally associate with H520. And ST16, which I normally associated with Typhoon H. And an android emulator. Which I don't use for anything. Can you clarify your setup, and for what you are using the emulator? I know all ST16S controllers are mislabeled as ST16, but I wanted to be sure. This will probably have to go to the open Forum to get a useful answer.
    Would you by any chance know where I can find the last firmware update software that was provided by Yuneec for the St-10+? This is being used with a Typhoon Q500+. Thank you
    Peter
    WTFDproject
    WTFDproject
    This link takes you to a repository of Q500 related firmware. The latest ST10+ is in the ST10+V01b31c.zip file near the bottom. You may already have the most current installed. If you do the update, refer to the instructions in this directory. The standard Yuneec instructions have led to many bricked controllers.
    • Like
    Reactions: FlexK9
    F
    FlexK9
    Thank you very much unfortunately I haven't flown my Q500 in quite some time and I need to update everything including the Q500 GUI software to all of the firmware for the transmitter ST10+, the Q500 and the CGO2 camera, I also need to get the CGO2 application. This is frustrating when companies remove products from production and don't leave the software on their website.
    Hi to all. So I have fixed/repaired just about everything known to man. So a friend gave me a Breeze 4k drone and an extra parts drone and circuit board for the eyes, along with all kinds of extras. . what I need now Is the lateset firmware for the breeze I can get. this quad has never had an update.
    WTFDproject
    WTFDproject
    Jared,
    You posted this in my "profile". You will get a better response by starting a new thread in the Breeze section of the Forum. The best contact for Breeze would be @DoomMeister. You may be able to find all the updates at this Dropbox location: Login - Dropbox
    Hello WTFDproject. Short question: Can I downgrade the firmware of the gimbal from v1.27 to V.1.25?
    WTFDproject
    WTFDproject
    No. It is the gimbal firmware I was talking about. Before you downgrade, I would contact a service center to ensure they have calibration capabilities in case things go wrong. The technicians may or may not know about the firmware conflict, and it may or may not be universal. But I'm not eager to do another one just to find out. ;)
    V
    Videomarketingdone
    Ok. Well I customized a steadycam with a typhoon h connector plate. The tilt and hold wont work. I've been told it is because it wont work with the V1.27 and it will with the V1.25.
    WTFDproject
    WTFDproject
    I've done what you suggested for the Q500 which I also have, on the Chorma, so have a Typhoon H named Chroma. But it won't recognize the Cam Cg03. Not sure if t's binding to Chroma. Without cam its moot. Will upgrade the SD card and see, as it says update error on Cam. Works fine on ST10. Seems like it recognised signal from a MK58. Perhaps hook a GoPro and see.
    WTFDproject
    WTFDproject
    I am not sure if you are working with an actual Chroma drone, or with a Typhoon H you have named Chroma. Please help me understand the drone model you are working with, and which controller you are using.
    it binds to controller but doesn't do anything when selecting calibrate Gimbal nothing happens .
    when the camera gets power the gimbal goes from 45 deg left to 45deg right back and forth ..
    I hope ive not imposed on you , and look forward to hearing your thoughts , they are greatly appreciated .. My son and i cant wait to get flying her
    S
    simonmac
    As mentioned to Steve if i cant fix it , we will just use it as a fixed camera type thing , like an fpv and just enjoy flying it ;)
    WTFDproject
    WTFDproject
    I'm working on a post on your new thread. I'm slower than most folks, but please be patient. I'm looking for a couple pictures I want to show you.
    S
    simonmac
    Take as long as you like, i'm thankful your spending any of your time at all helping me.
    Hi sorry follow on to that .
    I have powered the camera externally as the mainboard k fuse has blown, the pwr white wire and the green tx wire are still connected to the drones slide mount connector, I have checked all wires for continuity and there all good.
    The gimbal main board light is solid green and the camera led is flashing green.
    Hi i wonder if you can help me. A person on a Yuneec facebook group recommended i ask you as your the man in the know . thanks in advance .
    Issue is I dont have any control of my pan and tilt on my Yuneec h with cg03+ camera .. and the st16 controller
    I have recently bought the drone and it turns out It had been crashed !! as the camera wouldnt power on, Everything works, the video signal etc .
    I have a typhoon q500 4k. I was gonna do the firmware to it and I cant plug it into the wiring harness of the drone to the plug that goes to computer . I had noticed that there are 4 wires hanging with no plug on end. is there a diagram that tells me where thes wires go in to the plug that was still connected to the other end?
    WTFDproject
    WTFDproject
    Bigfoot,
    I can't add pictures here. I did add them to a PM I sent you, but they will be hard to see unless you download them. If you want to copy your message above to a new Thread in the Q500 section, I can put the same pictures there, and you can see them without downloading.
    bigfoot65
    bigfoot65
    thank you. I will see what I can do
  • Loading…
  • Loading…
  • Loading…
  • Loading…
  • Loading…

Members online

No members online now.

Forum statistics

Threads
20,955
Messages
241,599
Members
27,285
Latest member
hendrtiz